|
|
|
|
Product
Info • Technical
Data • Installation Instructions
MSDS:
USA: English
/ Spanish • Canada: English
/ French
|
HENRY
VinylLock 640
Pressure Sensitive Vinyl Flooring Adhesive
For
the installations of all vinyl tile and plank, and vinyl-backed
sheet flooring
- Use
as a pressure-sensitive or wet-set adhesive
- Excellent
Initial Grab
- Easy
Application
- Long
Working Time
- High
Ultimate Bond Strength
- Excellent
Moisture & Alkali Resistance
- Plasticizer
Migration Resistant
|
|
|
| Typical
Use: |
Traffic
Type: |
| Installation
of commercial and residential solid vinyl tile and plank,
and vinyl-backed sheet flooring. |
Moderate
to Heavy Commercial |
| Bonds: |
Bonds
To: |
| Solid
vinyl tile and plank, and vinyl-backed sheet flooring
to substrate. |
Porous:
Suspended APA approved wood, underlayment board, cementitious
underlayments, and dry concrete that is above, on or below
grade where moisture test levels meet the flooring manufacturer's
recommendations, but should not exceed 3 lbs./1000 sq.
ft./24 hours as determined by the calcium chloride moisture
test (ASTM F1869).
Non-porous: Staircases, terrazzo, ceramic tile,
metal, existing fully adhered non-cushion backed resilient
on all grade levels and poured polymeric floors. |
|
Warranty:
|
|
|
Back
to Top
|
TECHNICAL
DATA
| Base: |
Latex |
| Color: |
White |
| Taggant
Color: |
Yellow/Orange
|
| Open
Time: |
Wet
Set: 5 -10 minutes
Pressure Sensitive: 30-45 minutes |
| Working
Time: |
Wet
Set: 30 minutes;
Pressure Sensitive: 8 hours |
| Size: |
4
Gallon |
| Shipping
Unit: |
1
pail |
| Weight
Per Gallon: |
8.7
lbs |
| Quantity
Per Pallet: |
48
pails |
| Shelf
Life: |
One
year if not opened |
| Freeze-Thaw
Stable: |
To
10°F (-12°C) - Avoid low temperatures or multiple
freeze-thaw cycles |
| UPC
Information: |
USA:
0-8183300123-5
Canada: 0-8183300124-2 |
| VOCs: |
0
g/L; calculated and reported, SCQMD 1168 |
Back
to Top
INSTALLATION
INSTRUCTIONS
|
PREPARATION:
- Read
all installation instructions thoroughly prior to
installation.
- Store
flooring and adhesive, conditioning to the area
to be installed at a temperature of 65°F (18°C)
48 hours before, during and after installation.
- All
surfaces must be clean, dry and free of dust, grease,
paints, oils, sealers and
curing compounds or any other foreign materials
which may Interfere with proper
adhesion.
INSTALLATION:
HENRY 640 may be used as a "wet-set" adhesive
or as a pressure sensitive adhesive.
- Porous
Substrates: Spread adhesive with a 1/16"D
x 1/16"W x 1/16"A square notched trowel.
To use as a "wet-set" allow adhesive to
set open for 5 to 10 minutes before installing flooring.
To use as pressure sensitive adhesive, allow adhesive
to dry to the touch (approximately 30-45 minutes).
Install flooring within 8 hours. Roll flooring material
with a 75-100 lb. roller across width and length.
Avoid traffic for 12 hours after installation.
- Non-porous
Substrates: Spread adhesive with a 1/32"D
x 1/16"W x 1/32"A U-notched trowel. Allow
adhesive to dry to the touch (approximately 30-45
minutes). Install flooring within 8 hours. Roll
flooring material with a 75-100 lb. roller across
width and length. Avoid traffic for 12 hours after
installation.
|
Application
|
Recommended
Trowel
|
Coverage
|
| Porous
substrates |
|
Click on calculator to calculate how much you
need
|
| Non-porous
substrates |
|
Click on calculator to calculate how much you
need |
CLEANUP:
- Remove
wet adhesive residue with a clean, white cloth dampened
with soapy water. Use mineral spirits for dried
adhesive residue.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
|
|
