|
|
|
|
Product
Info • Technical
Data
Installation Instructions
MSDS:
USA: English
/ Spanish
• Canada: English
/ French
|
HENRY
482 LinoPro Premium Linoleum Adhesive
|
|
|
| Typical
Use: |
Traffic
Type: |
Installs
most residential and commercial
linoleum sheet flooring and glass backed linoleum floor
tiles. This product is for the professional who needs
an adhesive with a very strong bond and quick grab for
linoleum installations. |
N/A |
| Bonds: |
Bonds
To: |
| Residential
and commercial linoleum sheet flooring and glass backed
linoleum floor tiles. |
Suspended
A.P.A. approved wood, underlayment board, cementitious
underlayment, terrazzo, ceramic tile, metal, poured polymeric
floors and dry concrete that is above, on or below grade
where there is less than 3 lb./1000 sq. ft./24 hrs. as
determined by the calcium chloride moisture test (ASTM-F-1869);
existing fully adhered resilient on all grade levels.
|
|
Warranty:
|
|
|
Back
to Top
|
TECHNICAL
DATA
| Base: |
Filled
Latex |
| Color: |
Tan |
| Taggant
Color: |
Yellow/Orange |
| Next
Generation: |
Yes |
| Open
Time: |
10
Minutes over porous, 10-20 minutes over non-porous |
| Working
Time: |
40-50
minutes |
| Size: |
4
Gallon |
| Shipping
Unit: |
Pail |
| Weight
Per Gallon: |
9.79
lbs |
| Quantity
Per Pallet: |
48
pails |
| Shelf
Life: |
One
year if not opened |
| Freeze-Thaw
Stable: |
To
10°F (-12°C) - Avoid low temperatures or multiple
freeze-thaw cycles |
| UPC
Information: |
4
Gallon: 0-81833-000001-6 |
Back
to Top
INSTALLATION
INSTRUCTIONS
- DIRECTIONS:
PREPARATION
- Read
installation instructions and MSDS thoroughly prior
to installation.
- All
surfaces must be clean, dry and free of dust, grease,
paints, oils, sealers and curing compounds, or any
other foreign materials which may interfere with
proper adhesion. Condition the area to be installed,
adhesive and flooring at 65°F (18°C) or
above for 48 hours before, during and 48 hours after
installation.
- Refer
to linoleum manufacturer’s specific recommendations.
INSTALLATION
- Upon
opening the container, stir any liquid that is on
the surface into the adhesive.
- Full
spread adhesive using recommended trowel.
- Before
installing floor, allow adhesive to set open up
to 10 minutes. On a non-porous substrate, allow
10-20 minutes open time.
- If
adhesive dries or skins over, the adhesive must
be scraped up and fresh adhesive needs to be applied.
- After
appropriate open time, install floor.
- Within
25 minutes, cut, fit and reposition as recommended.
- Roll
floor in both directions with a 75-100 lb. roller
or flooring manufacturer’s recommended roller
across width and length and and heat weld seams
as recommended.
|
Application
|
Recommended
Trowel
|
Coverage
|
| All
(excepting below) |
|
145-170 sq ft/gal
|
| Glass
Backed Linoleum Tiles over Non-Porous Subfloor
only |
|
225-275 sq ft/gal) |
Click on the icons above to
calculate the amount of product you need!
CLEANUP:
- Wet
Adhesive: Clean, white cloth dampened with soapy
water.
- Dried
Adhesive: Clean, white cloth dampened with mineral
spirits; carefully following warnings on the container.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
|
|
