|
|
|
|
Product
Info • Technical
Data
Installation
Instructions
MSDS:
USA: English
/ Spanish
• Canada: English
/ French
|
HENRY
430 ClearPro™ Clear Thin Spread Floor Tile Adhesive
|
|
|
|
| Typical
Use: |
Traffic
Type: |
| Installation
of vinyl composition tile (VCT) and asphalt tile. |
Not
Designated |
| Bonds: |
Bonds
To: |
| Vinyl
composition tile (VCT) and asphalt tile. |
Concrete,
existing asphalt “cutback” adhesive residue
which is smooth with no ridges or puddles evident, wood
and wood underlayments; wood subfloors should be suspended,
existing well-bonded resilient flooring; not perimeter-bonded
or cushion-backed, ceramic tile, terrazzo, marble, and
polymeric-poured floors, properly mixed and applied
powder underlayments and embossing levelers, primed,
poured-in-place gypsum subfloors, radiant-heated subfloors
where the surface temperature does not exceed 85°F
(29°C)
|
| Warranty: |
| HENRY's Best 10 Year Warranty |
Back
to Top
|
TECHNICAL
DATA
| Base: |
Water-based/rubber-resin |
| Color: |
Beige |
| Taggant
Color: |
Yellow/Orange |
| Open
Time: |
30-90
minutes |
| Working
Time: |
24
hours NOTE: Working times vary based on job conditions,
substrates, temperature and humidity. |
| Size: |
Quart,
Gallon, 4 Gallon |
| Shipping
Unit: |
Quart:
12 quarts/ctn
Gallon: 4 gallons/ctn
4 Gallon: 1 pail |
| Weight
Per Gallon: |
8.4
lbs |
| Quantity
Per Pallet: |
Quart: 40 ctns
Gallon: 30 ctns
4 Gallon: 48 pails |
| Shelf
Life: |
One
year if not opened |
| Freeze-Thaw
Stable: |
To
10°F (-12°C) - Avoid low temperatures or multiple
freeze-thaw cycles |
| UPC
Information: |
Quart: 0-81833-43030-1
Gallon: 0-81833-43040-0
4 Gallon: 0-81833-43095-0 |
Back
to Top
INSTALLATION
INSTRUCTIONS
|
DIRECTIONS:
Refer to tile manufacturer’s
specific recommendations. Condition the area to be installed,
adhesive and flooring at 65°F (18°C) or above
for 48 hours before, during and 48 hours after installation.
Floor must be sound, smooth, dry, clean and free of
excessive moisture or alkali. Remove dirt, wax, loose
paint and all other foreign matter that would interfere
with a good bond such as curing agents and sealers.
Moisture test results should meet the flooring manufacturer’s
recommendations but should not exceed 5 pounds/1000
sq ft/24 hours.
- Stir
any liquid on the surface into the adhesive.
- Full
spread adhesive using the recommended trowel.
- Before
installing tile, allow adhesive to set open until
dry to the touch (tacky but no transfer to fingers),
30-90 minutes.
- After
appropriate open time, install tile. Within 24 hours,
install and fit all tile as recommended by the tile
manufacturer.
- Roll
with a 100 lb. roller if recommended by the tile manufacturer.
- Do
not wet wash or strip tile for 5 days after installation.
|
Application
|
Recommended
Trowel
|
Coverage
|
| 1/8"
tile |
|
350-400 sq. ft.
|
Click
on the icons above to calculate the amount of product
you need!
CLEANUP:
- Wet
Adhesive: Clean, white
cloth dampened with soapy water.
- Dried
Adhesive: Clean, white
cloth dampened with mineral spirits; carefully following
warnings on the container.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
Back
to Top
|
|
