|
|
|
|
Product
Info • Technical
Data
Installation
Instructions
MSDS:
USA: English
/ Spanish
• Canada:
English
/ French
|
HENRY
351 FastPro™ Fast Grab Carpet Adhesive
|
|
|
|
| Typical
Use: |
Traffic
Type: |
| Installation
of most commercial carpets. |
Moderate
to Heavy Traffic Areas |
| Bonds: |
Bonds
To: |
| Jute,
polypropylene (ActionBac™), latex unitary, urethane
foam, unitary ActionBac, hot melt, or latex foam backed
and nonbacked needle-punched. |
Concrete,
underlayments, wood substrates, terrazzo and existing
resilient on all grade levels as recommended by the carpet
manufacturer. |
| Warranty: |
| HENRY's Best 10 Year Warranty |
Back
to Top
|
TECHNICAL
DATA
| Base: |
Water-based/rubber-resin |
| Color: |
Tan |
| Taggant
Color: |
Yellow/Orange |
| Next
Generation: |
Solvent-free,
nonflammable |
| Open
Time: |
Stiff
or nonporous backed carpets over nonporous substrates:
Allow adhesive to set open to start to develop tack and
apply to floor. All other carpet: Install immediately
into wet adhesive |
| Working
Time: |
40
minutes NOTE: Working times vary based on job conditions,
substrates, temperature and humidity. |
| Size: |
4
Gallon |
| Shipping
Unit: |
4
Gallon: 1 pail |
| Weight
Per Gallon: |
10
lbs |
| Quantity
Per Pallet: |
4
Gallon: 48 pails |
| Shelf
Life: |
One
year if not opened |
| Freeze-Thaw
Stable: |
To
10°F (-12°C) - Avoid low temperatures or multiple
freeze-thaw cycles |
| UPC
Information: |
4
Gallon: 0-42369-08853-4 |
Back
to Top
INSTALLATION
INSTRUCTIONS
|
DIRECTIONS:
Refer to carpet manufacturer’s
specific recommendations. Condition the area to be installed,
adhesive and carpet at 65°F (18°C) or above
for 48 hours before, during and 48 hours after installation.
Floor must be sound, smooth, dry, clean and free of
excessive moisture and/or alkali. Remove dirt, wax,
loose paint, and all other foreign matter that would
interfere with a good bond such as curing agents and
sealers.
- Stir
any liquid on the surface into the adhesive.
- Full
spread adhesive using the recommended trowel.
NOTE: Recommended trowel sizes are guidelines only,
and are minimum requirements. Rough, porous concrete
and heavily textured carpet backings may require deeper
notches. A 100% transfer of adhesive into the carpet
backing, while maintaining full coverage of the substrate,
must be obtained.
- Before
installing stiff or nonporous backed carpets over
nonporous substrates, allow adhesive to set open to
start to develop tack. Install all other carpet immediately
into wet adhesive.
- Within
40 minutes, cut, fit and reposition as recommended
by the carpet manufacturer.
- Roll
floor in both directions with a 75-100 lb. roller
and seal seams as recommended by the carpet manufacturer.
Stiff carpets should be rolled again after 2 hours.
Restrict heavy traffic over carpet for 24-48 hours.
- Protect
carpet from exposure to water from cleaning and other
sources for a minimum of 30 days after installation.
|
Application
|
Recommended
Trowel
|
Coverage
|
| Latex
and urethane foam backed carpets |
|
144-162 sq. ft.
(16-18 sq yds/gal)
|
| Other
carpet backings |
|
90-108 sq. ft.
(10-12 sq yds/gal)
|
Click
on the icons above to calculate the amount of product
you need!
CLEANUP:
- Wet
Adhesive: Clean, white
cloth dampened with soapy water.
- Dried
Adhesive: Clean, white
cloth dampened with mineral spirits; carefully following
warnings on the container.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
Back
to Top
|
|
