|
|
|
|
Product
Info • Technical
Data
Installation Instructions
MSDS: USA: English
/
Spanish • Canada: English / French
|
NEW! Click
here to learn more!
HENRY
1171 SureLock Wood Flooring Adhesive
-
Excellent
Initial Grab
-
High
Early Strength
Development
-
Excellent
Ultimate Bond
Strength & Elongation
-
Enhanced
Moisture &
Alkali Resistance
-
Solvent-Free & Low Odor
|
|
|
|
| Typical
Use: |
Traffic
Type: |
| Installs
engineered wood plank and wood parquet flooring. |
N/A |
| Bonds: |
Bonds
To: |
| Wood
parquet up to 5/16” thick and engineered wood
plank up to 9/16” thick and 4.5” wide.
Do not use to install stair nose or reducers. |
Concrete,
underlayments, wood substrates, terrazzo and existing
resilient on all grade levels
as recommended by the flooring manufacturer. |
| Warranty: |
| HENRY's Best 10 Year Warranty |
Back
to Top
|
TECHNICAL
DATA
| Base: |
Latex |
| Color: |
Light
Yellow |
| Taggant
Color: |
Yellow/Orange |
| Next
Generation: |
Yes |
| Open
Time: |
None;
NOTE: works best with a few minutes of open time |
| Working
Time: |
30
minutes; NOTE: Working times vary due to temperature
and humidity |
| Size: |
4 Gallon |
| Shipping
Unit: |
1 pail |
| Weight
Per Gallon: |
11.7
lbs |
| Quantity
Per Pallet: |
48 pails |
| Shelf
Life: |
One
year if not opened |
| Freeze-Thaw
Stable: |
To
10°F (-12°C) Avoid low
temperatures or multiple
freeze/thaw cycles |
| VOC's: |
1
g/L; calculated and reported, SCAQMD 1168 |
| UPC
Information: |
0-81833-00030-6 |
Back
to Top
INSTALLATION
INSTRUCTIONS
|
DIRECTIONS:
- Read installation instructions
and MSDS
thoroughly prior to installation.
- All
surfaces must be sound, smooth, dry, clean,
free of excess moisture and alkali. Remove dirt,
wax, loose paint and all foreign matter that would
interfere with a good bond, such as curing agents
and sealers. Condition the area to be installed,
adhesive and flooring at 65°F (18°C) or above
for
48 hours before, during and 48 hours after
installation.
- Refer
to the wood flooring manufacturer’s specific
recommendations for subfloor preparations.
- Always
run a calcium chloride and alkali test
over
concrete on any grade level. For accurate results,
curing agents must be removed in areas where
tests will be run. Moisture test results should
meet the flooring manufacturer’s recommendations,
but
should not exceed 3lbs./1000 sq.ft/24 hrs., as
determined by the calcium chloride moisture
test
(ASTM-F -1869). Alkali readings should be 5 to
9.
INSTALLATION
TIPS:
- Stir
any liquid on the surface into the adhesive
and full spread adhesive using recommended trowel.
- Before
installing floor, allow adhesive to set
open a few minutes.Do
not spread more adhesive than
can be covered within 30 minutes.
- Do
not allow a heavy film to form on the surface
of
the adhesive. If the adhesive dries
or skins over, the adhesive must be scraped
and fresh adhesive
needs to be applied.
- Press
wood flooring down firmly, lifting a piece
occasionally
to be sure the adhesive is fully
bonding to the backing.
- Allow
1/2” space around perimeter of
room and stationary
objects for normal wood flooring
expansion.
- Roll
floor with a heavy roller, if
recommended by the
wood flooring manufacturer. Adhesive
must set overnight before exposing
to traffic or
applying finish.
|
Application
|
Recommended
Trowel
|
Coverage
|
| Engineered
Wood Plank |
|
180-220 sq. ft./4 gal
|
| Wood
Parquet |
|
200-240 sq. ft./4 gal
|
| Wood
Parquet |
|
200-240 sq. ft./4 gal
|
Click
on the icons above to calculate the amount of product
you need!
CLEANUP:
- Wet
Adhesive: Clean,
white cloth dampened with soapy water.
- Dried
Adhesive: Clean,
white cloth dampened with mineral spirits; carefully
following warnings on the container.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
Back
to Top
|
|
