|
|
|
|
Product
Info • Technical
Data
Installation Instructions
MSDS: USA:
English / Spanish
• Canada: English / French
|
HENRY
117 Multipurpose Construction Adhesive
|
|
|
|
| Typical
Use: |
Traffic
Type: |
| Installation
of paneling, drywall, particleboard, moldings and FRP
panels. |
N/A |
| Bonds: |
Bonds
To: |
| Wood wall paneling,
predecorated wallboard, plywood, gypsum drywall, wood
or metal moldings, furring strips, wall decorations, particleboard,
hardboard, ceramic tile repairs and metal fixtures. Do
not use for wood flooring. When installing polystyrene
foam insulation, surface temperature should not exceed
90°F (32°C) or etching of foam may result. |
Concrete, wood
or metal framing studs, furring strips, wood, dry plaster
and gypsum drywall on all grade levels as recommended
by the panel manufacturer. When installing over below-grade
concrete where moisture can penetrate from back, attach
furring strips with mechanical fasteners and adhesive,
and then adhere panels. |
| Warranty: |
| HENRY's Best 10 Year Warranty |
Back
to Top
|
TECHNICAL
DATA
| Base: |
Solvent-based |
| Color: |
Tan |
| Taggant
Color: |
Yellow/Orange |
| Open
Time: |
Lay
in immediately |
| Working
Time: |
15
minutes NOTE: Working times vary based on job conditions,
substrates, temperature and humidity. |
| Size: |
30oz,
5 Gallon |
| Shipping
Unit: |
30
oz : 12 cartridges/ctn
5 Gallon: 1 pail |
| Weight
Per Gallon: |
9.4
lbs |
| Quantity
Per Pallet: |
30
oz : 60 ctns
5 Gallon: 36 pails |
| Shelf
Life: |
Best
if used within one year |
| Freeze-Thaw
Stable: |
Not
affected |
| UPC
Information: |
30
oz : 0-81833-11705-9
5 Gallon: 0-81833-11770-7 |
Back
to Top
INSTALLATION
INSTRUCTIONS
|
DIRECTIONS:
Refer to panel manufacturer’s
specific recommendations. Condition the area to be installed,
adhesive and panels (laying flat) at 65°F (18°C)
or above for 48 hours before, during and 48 hours after
installation. Surface must be sound, smooth, dry, clean
and free of excessive moisture or alkali. Remove dirt,
wax, loose paint and all other foreign matter that would
interfere with a good bond such as curing agents and
sealers. This adhesive should not be used in situations
where odors may be transmitted to foodstuffs.
- Stir
any liquid on the surface into the adhesive.
- Full
spread adhesive on back of panel using recommended
trowel. Do not leave bare spots. Press down firmly
on the trowel to avoid adhesive between ridges.
- Dry
fit first panel vertically in a corner where walls
intersect. Mark corner edge with dividers. Trim marked
edge with saw to fit corner.
- Place
back in corner and mark any cutouts. Use a fine-toothed
saw to make cutouts. Mounting screws can be cut with
a utility knife after panel is installed.
- Place
panel against wall within 15 minutes. Press firmly
over entire surface working from center to edges so
that entire back of panel is in full contact with
wall.
- If
wall irregularities prevent the adhesive from holding
panels tight to the wall, press firmly again after
10 minutes, and use temporary bracing or a finishing
nail to hold while the adhesive sets.
- For
channel moldings and for permanent fasteners, follow
the panel manufacturer’s recommendations. Do
not fit panels too tightly into moldings. A minimum
1/16" expansion space is needed.
|
Application
|
Recommended
Trowel
|
Coverage
|
| |
|
50-60 sq. ft.
|
Click
on the icons above to calculate the amount of product
you need!
CLEANUP:
- Wet
Adhesive: Clean,
white cloth dampened with mineral spirits.
- Dried
Adhesive: Clean,
white cloth dampened with mineral spirits; carefully
following warnings on the container.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
Back
to Top
|
|
